The kitchen remodel continues!
Here’s a reminder of what the kitchen looked like during our initial walk-through with the plain plywood cabinet doors, tan walls and frig shoved randomly into the former pantry next to the stove.
After a splash of color, painted fixtures, some repurposed decorations and some new picture frame cabinets the room now looks like this:
So far we’ve painted all the icky brass fixtures without removing them–yeah!
But the hands down best part of this room is the custom picture frame cabinets!
Want to make your own?
First: The Disclaimer
Ana White I am not.
Unfortunately I have no drafting skills, no working knowledge of Google Sketch and I stink at trying to use the draw tool in Microsoft Word. So, instead you’ll have to tag along while I walk you through this project old school style. Ideally I’d have enough scrap wood from four years ago to just make another frame door to show you. But since I don’t and spending money is a no-no, I’m going to do the next best thing and show you exactly how to building them … using cardboard.
I have not included exact dimensions since everyone’s cabinets will vary in size. What I have included is a few specific dimensions for the width of the frame pieces and then you can cut the length to fit your doors.
The good news is that this project is so easy to build, so customizable and so dirty cheap – as in about $7 per door cheap — that the whole tutorial-out-of-cardboard-without-exact-measurements won’t even phase you.
The bad news is that, as you’ll remember from this post, most of the “during” pictures STINK and were taken in 2007 before I had any idea what blogging was or how to take pictures.
Phew. Now on to building!
Cabinet Doors: 3/4” plywood or high-grade particle board
1 – 4’ x 8’ sheet will yield approximately 7 cabinet doors: 2 small doors for over frig or range and 5 standard doors.
“Frames” For Each Door: 1/8” Masonite / Hardboard
Sold in 4’ x 8’ sheets for about $7 each. I found mine in the trim section.
And of course you’ll need:
* Wood Glue * 1” Finish Nails * Chop Saw * Sand paper
If You’re Using Existing, Flat-Front Cabinet Doors …
Remove cabinet doors and label, remove hardware, sand, wipe down and let dry.
(If you have flat front, laminate-covered doors, don’t try and build over top of them–the paint won’t stick very well. Go with new plywood ones.)
If You’re Making New Cabinet Doors …
Cut new doors from 3/4” plywood, sand, wipe down and let dry.
Do yourself a favor and have the Masonite board pre-cut at the hardware store in 2.25” x 8’ and 2.5” x 8’ strips. Have the last strip from the board be cut to 2” x 8’. These long strips can then be cut down to the exact length you need for each cabinet door.
Building The Frames!
There are three layers to these doors: plywood base, under frame and top frame.
The under frame pieces are 2.25” wide
The top frame pieces are 2.5” wide.
Small “Single Frame” Doors
Attach the under frame to the base using 2.25” strips in a “U” shape.
Glue under frame pieces to the base making sure frame pieces are flush with the door edges.
Measure the inside area for the picture insert and make sure it fits. (This is the easiest time to do this step.)
Attach the 2.5” strips of the top frame across the top and bottom edge first, then along sides using wood glue.
(Sorry, forgot to remove the insert before taking this picture. No, don’t leave insert in while gluing.)
Use a 1” finish nail in each corner.
Large “Double Frame” Doors
Attach the under frame to the base using 2.25” strips in an “E” shape using wood glue.
NOTE: The middle section of the “E” is only 2” wide. If you use a 2.25” piece, the top frame will not sit right.
Also make sure that the picture insert openings are on the opposite side of where the door hardware will be attached.
Measure the inside area for the picture inserts.
Attach the 2.5” strips of the top frame down the long outside edges first, then along top, middle and bottom of the door using wood glue.
Use a 1” finish nail in each corner and then center frame piece.
When glue has dried, sand all doors lightly, wipe down with a damp rag and let dry.
Paint doors with one coat of primer and two coats of semi- or high gloss paint. Distress edges lightly with sand paper to bring out the details of the frame and stain if desired. Finish with a coat or two of polyurethane.
(I skipped this step and have to do regular touch ups. Oops.)
Sand cabinet insides and sides, prime, paint, distress and seal as with the cabinet doors.
(Lousy photo of cabinets painted black inside and out to match the cabinet doors)
Reattach hardware, hang doors and
Picture Frame Cabinet Doors for $7 each
and a whole new look for your kitchen!
Not that the classic look doesn’t rock, but here’s what you can do with these cute, framed-out bad boys and some cheapie $0.50 poster board:
(very first gallery cabinets in 2007 – regular digital prints taped to poster board)
– or –
TISSUE PAPER / FABRIC / WRAPPING PAPER
(tissue paper attached to poster board with spray adhesive – made to match my Easter tree)
– or –
(poster board + old house paint. Loved the look, but hate that I’m a lousy hand painter. Total CRAFT FAIL—ha! I’ll probably try this look again using vinyl and my silhouette machine.)
– or –
HOLIDAY / VINTAGE
(poster board + computer printed images from Graphics Fairy)
– or even a –
BULLETIN BOARD DOOR
(poster board + old VHS tape hot glued in place)
And can’t you just imagine inserts covered with
BURLAP? STENCILED BURLAP?
Or maybe even
UPHOLSTERED and TUFTED FABRIC?
SHEET METAL or CHALKBOARD PAINT?
I know. It’s crazy.
I kinda want a whole wardrobe for my cabinet doors now and it is such a good thing.
A few THRIVE hints to save you some headaches
* I don’t have glass fronts in my doors and it’s no big deal. I love seeing the texture of the inserts up close and like being able to add 3-D touches. I’ve rarely had a problem with splatters or kid schmeer ruining inserts. And when the inserts start to show their wear, I just grab another .50 piece of poster board and make new ones. (You can also tape a piece of acetate or clear cellophane to each insert if you’d like them to be wipe-able).
* If you do want to add glass or Plexiglas to your frames, using 3/16” Masonite will allow enough room for the insert and 1/8” glass/Plexiglas.
* For the bottom cabinets, skip the under frame all together and just build the top frame straight to the base. That way the bottom doors will have the same look and feel as the framed doors without the hassle of the real thing.
*Make sure the openings for the inserts are on the opposite side of the hinges or you won’t be able to get pictures in or out.
* To save even more money, I decorate the front and back of each insert.
* In years past I’ve added vinyl lettering for holidays for a fun touch.
* To help me keep track of which insert goes where, I lettered my cabinets and then mark the bottom corner of each insert with the corresponding letter and which direction it goes. When I forget that step, I may or may not end up with an insert with a pattern going the wrong direction.
So there you go!
Hope you have fun making my crazy cheap, super simple picture frame cabinets! Please leave a comment or drop me an email if you have any questions.
Linking up to: